JANOME 900CPX Instrukční brožura

INSTRUCTION BOOKCOVER PRO 900CP

6Raising or Lowering the Presser FootBy raising or lowering the presser foot lifter, the presserfoot goes up or down. * While in operation, keep the p

7Adjustment of Stitch LengthTo adjust the stitch length, turn the dial.The larger the number, the longer the stitch.The stitch length can be adjusted

8Changing NeedleTurn the handwheel toward you to raise the needle to itshighest position.q HandwheelThen loosen the needle clamp screw for the needle

9Setting the Thread Guide BarPull the thread guide bar up as far as it will go.Turn the thread guide bar so that the thread guides areright above the

10Thread the machine in the following order:1 Left needle thread2Right needle thread3 Looper threadThreading the MachineRaise the presser foot lifter.

11wThreading the needlesThread each needle in the following steps:1 Draw the thread through the Left side threadguide bar from back to front as shown

123Hold the thread at both ends and tug gently toensure the thread is correctly inserted betweenthe tension disks. ( If the presser foot lifter israis

13Threading the looperThread the looper in the following steps:1Draw the thread through the right side threadguide bar from back to front as shown (A)

143Hold the thread at both ends and tug gently toensure the thread is correctly inserted betweenthe tension disks. ( If the presser foot lifter israis

1544 2STITCH TYPESCover StitchThis stitch forms 5 mm wide two parallel rows of thestraight stitch on the right side, widely used on cuffs andstretch w

IMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance, basic safety precautions should always be followed, including thefollowings:Read all

1633 2Chain StitchThis stitch is sewn with a single needle and forms a chainof looper thread on the wrong side of the fabric.This is a durable and fle

17Finishing the SeamTo achieve the best results, use a piece of scrap fabric atthe beginning and end of the seam.Beginning of the seam1 Raise the pres

18Removing the Fabric in the Middleof the Stitching1Raise the needles to their highest position by turningthe handwheel toward you.q Handwheel2 Raise

19Hemming with the Cover Stitch1 Fold up the edge of the fabric to the wrong side andpress.2Draw a line with a tailor’s chalk on the right side of the

20Cover Stitch ApplicationsAttaching laces and tapesq Tape or lacew Right side of the fabrice Wrong side of the fabricAttaching elasticsq Right side o

21CARE OF YOUR MACHINECleaning the Feed Dogs and Looper AreaWARNING:Turn the power switch off and unplug the machinebefore cleaning.NOTE:Do not disman

22ProblemNeedle threadbreaks.Needle bends orbreaks.Skipped stitchesSeam puckeringMachine does notoperate.Cause1. The machine is not threaded correctly

795-800-003 (E)Printed in Taiwan

1TABLE OF CONTENTSKNOW YOUR MACHINENames of Parts ... 2

2KNOW YOUR MACHINENames of Partsq Differential feed dialw Stitch length diale Handwheelr Spool standt Spool holdery Spool pinu Thread guide bari Threa

3Standard Accessoriesq Set of needles: 2 X #80/12, 3 X #90/14(Schmetz EL X 705)w Screwdriver (Large)e Screwdriver (Small)r Tweezerst Netsy Spool holde

4GETTING READY TO SEWConnecting the Machine to the Power Supply1 Turn off the power switch, and connect themachine plug to the machine socket.2 Connec

5How to Turn the HandwheelAlways turn the handwheel toward you(Counterclockwise).q HandwheelOpening and Closing the Looper CoverTo open: (A)While push